Moog Videolarm AD16CH2 Instructions d'exploitation Page 1

Naviguer en ligne ou télécharger Instructions d'exploitation pour Accessoires pour caméras de sécurité Moog Videolarm AD16CH2. Moog Videolarm AD16CH2 Manuel d'utilisatio

  • Télécharger
  • Ajouter à mon manuel
  • Imprimer
  • Page
    / 6
  • Table des matières
  • MARQUE LIVRES
  • Noté. / 5. Basé sur avis des utilisateurs
Vue de la page 0
!
Retention Screw
1/4-20 Screws
Spacers
Speci cation Cat alog
Number Section
INSTRUCTIONS 5265 1b
MODEL: Outdoor Dust Free Housing
AD8CH2 & AD16CH2
PRODUCT INSTRUCTIONS
2525 Park Central Blvd. • Decatur, Ga 30035 • (770) 987-7550 • 800-554-1124 U.S. & Canada • Fax 800-826-0366 • www.videolarm.c om
ective Date: 02-02-2009
INCLUDES MODEL: AD16CH2
GENERAL INSTRUCTIONS:
Use only with Class 2 Power Supply
HARDWARE KIT
3 Cable Tie
2 BHCS, 1⁄4-20 x 1⁄4-inch
1 BHCS, 1⁄4-20 x 5⁄8-inch
1 BHCS, 1⁄4-20 x 3⁄4-inch
1 BHCS, 1⁄4-20 x 1⁄2-inch
1 BHCS, 1⁄4-20 x 3⁄8-inch
1 BHCS, 1⁄4-20 x 11⁄4-inch
2 0.4 mm (0.016-inch) Plastic Spacer
1 1.65 mm (0.065-inch) Plastic Spacer
1 3.9 mm (0.154-inch) Plastic Spacer
1 7.4 mm (0.292-inch) Plastic Spacer
1 9.8 mm (0.385-inch) Plastic Spacer
1 3⁄8-inch NPT Plug
2 Pull Seals
CAMERA INSTALLATION
Figure 1
NOTE: Do Not Exceed 30 VAC Input.
Operation above 30 VAC violates low voltage operation
(Class 2 Speci
cations). Normal operation is 24 VAC.
TOOLS REQUIRED
Phillips head screwdriver
5⁄32-inch (or 4 mm) hex wrench
5⁄16-inch (or 8 mm) hex wrench
Wire cutter/stripper/crimper tool
1. Remove the cradle from the housing by lowering the retaining
screw completely on the bottom rear of the housing.
2. Turn slot on the retaining ring, located on the rear cap, to the
bottom of the housing (Figure 1).
3. Remove the cradle assembly by pushing gently on the metal
part of front cap and simultaneously grasping the rear handle and
pulling the cradle assembly out of the housing. Be sure to keep
the edges of the end caps clean and free of scratches (Figure 2).
Figure 2
RATINGS
NEMA-3R and IP54
The HS9384 Series housings include a “breather hole in the
front end cap. The “breather hole prevents the accumulation
of moisture inside the housing when installed in areas of high
humidity. With the “breather hole open, the AD16 housing meets
the enclosure rating requirements of NEMA-3R and IP54.
NEMA-6P and IP68
For installations requiring an enclosure rating of NEMA-6P or
IP68, the breather hole must be plugged using the pull seal (Part
No. 315 2569 001) provided in the hardware kit. Refer to Final
Assembly under INSTALLATION for proper installation.
4. Place the camera/lens combination into the cradle assembly.
Position the camera/lens 1 mm (0.04-inch) away from the
faceplate. The camera/lens is secured to the cradle with a
1⁄4-20 button head cap screw (BHCS) and the appropriate
plastic spacer (Figure 3).
Figure 3
© 2009, Videolarm, Inc. All Rights Reserved
Vue de la page 0
1 2 3 4 5 6

Résumé du contenu

Page 1 - PRODUCT INSTRUCTIONS

!Retention Screw1/4-20 ScrewsSpacersSpeci cation Cat alog Number Se

Page 2

SealCapSealGlandDualMalePortion!!3/8-inchNPTPlugM4ScrewTerminal Lug!!2WIRING1. Use the left liquid-tight fi tting of the housing to route the p

Page 3

FrontFaceBreatherHoleLongEndHeadFrontofEndcapPullSealBreatherHoleCradleFrontEndcapRearFaceofHeadShouldBeFlushwithFrontFaceofFrontEn

Page 4

4EXPLODED VIEWRef No. Part Number Qty. Part DescriptionHeyco Fitting Kit – 315 3802-0017 - 2 3⁄4 NPT8 - 1 3⁄8 NPTCradle Assembly Ki

Page 5 - 1-800-554-1124

! CAUTIONRISK OF ELECTRIC SHOCK! CAUTION: TO REDUCE THE RISK OF ELECTRICAL SHOCK, DO NOT EXPOSE COMPONENTS TO WATER OR MOISTURE.SAFETY PRECAUTIONS

Page 6 - Online Option 2: Mail-In

Product Registration/WarrantyThank you for choosing Videolarm. We value your patronage and are solely committed to providing you with only the highes

Commentaires sur ces manuels

Pas de commentaire